piros365's blog
Lonsdor K518ISE program match the smart card
1 press the start button, open the driver door;
2 the system tries to get the password
if the model can be read out, please select the password. If the vehicle password cannot be recognized, please read EEPROMdata and put it into Lonsdor K518ISE. Then do as follows:
① with the USB cable to connect Lonsdor K518ISE programmer to the computer, the computer will display K518 host internal storage;
② copy the .bin (lowercase) file of CPU data to the Lonsdor K518ISEhost’s customfile directory;
③ return to the smart card match operation, select the import file for secret read.
3 insert the smart key need to match . the first key match is completed; please follow the pop-up to continue to match another keys;
4 remove the smart key if you do not continue to match keys
Renault key programming is complete.
In detail… look here:
Lonsdor K518 Program Renault Koleos 2011 Smart Key
Step 1: Remove BCM
Disassemble BCM immo box and find CPU chip XDT384
Step 2:VVDI Prog read EEPROM data
Open VVDI-Prog software
Select Renault-BCM-XDT384
Follow vvdi programmer wiring diagram to connect
Read eeprom data and save data to bin format
Connect K518 host with laptop via USB cable
You will see “customfile” folder on K518 software
Copy the eeprom bin file to “customfile” folder
Step 3: Lonsdor K518 program Smart Key
Re-install BCM from car
Connect Lonsdor K518 key programmer with vehicle via diagnostic socket
Select Renault->By System->Smart Key->Immobilizer system 2->Program smart key
Press on the Start button, press YES to continue
Open the door on driver side
Lonsdor K518ISE Auto Key Programmer shows unable to identify pin code automatically.
Follow guides below: (We have done 1 and 2)
1.Connect K518 host with laptop via USB cable. You’ll see “customfile” folder
- Copy eeprom bin file to “customfile” folder
- select eeprom bin file on “customfile” folder
Select Renault BCM data.bin
Insert a new smart key to be programmed into the card slot
Configuring system
Program success. Press YES to program next key
Insert next smart key into card slot
Program success.
Remove smart key
Key learning success
MB SD Connect Compact 4 wifi verson,supports reading out and erasing trouble code,reading the real-time data of sensor and actuator, coding and programming
MB SD Connect Compact 4 Star FAQ
MB STAR C4 Customer share:
Q: How to set MB SD C4 WIFI?
A: Firstly, disconnect the local areal connection, then connect the sdconnect 4 with the car and start the car, finally connect to the wireless connections, please follow the next instructions to set: click Configuration-MUX-Register/configure, under the "General information", select name "04" and then tick off "Wlan parameters, road", then set the following parameters: IP address: 192.168.2.200, Network screen: 255.255.255.0, Encryption: WEP/Hex, Key: aaaaaaaaaaaaaaaaaaaaaaaaaa (26 a in total), we have video tutorial, please click column "Video" to watch or contact our customer service to send you.
Q: Why MB STAR C4 is unable to connect with the computer; even after I try LAN cable.
A: It needs to set the IP address. How to set the IP address?
Start-Connect to all connections-Local Area Connection-right click "Properties"-Internet Protocol-Use the following IP address, IP address: 172.29.127.114, Subnet mask: 255.255.0.0, finally click "Ok", we have video tutorial, please click column "Video" to watch or contact our customer service to send you.
Q: When I start DAS, it says that, I am using the developer version. In some menus however the software does not seem to be a developer version.Is it or is it not a developer version? am NOT connected to the internet when diagnosing a car. Only the SD-Box is connected to the notebook via WLAN. Could that be the problem?
A: Have you set the "sdc4" well? Could you please do a self-checking for your device? Then show me the result of the self-checking. Please refer to the following steps of self-checking.
A: Did you have the SD C4 set well? Please follow the next instructions to have a self-test, and then send us the self diagnostic report.
Q: MB SD STAR C4 is unable to self-test?
A: check whether the COM PORT is COM2, if it is, there are four possible reasons: 1) the COM PORT has problem; 2) MB SD C4 and the computer has a poor connection. 3) The cable or SDC4 doesn’t work; 4) SD C4 disconnect with the car.
Q: When I do self-diagnosis for MB, I got error message: 3001 Error.
A: Self-diagnostic has error not suggest MB SD C4 has problem. The aim of self-diagnosis is to check whether STAR C4 connect well with the computer and the car, whether the IP address and parameter is set correctly, whether the SD connect c4 and the driver has successful communication. We have video tutorial on how to do self diagnosis for SD C4, please follow it to operate, if you are able to self-diagnostic, it suggests MB SD C4 settings is OK, the connections is OK and it has communication between MB SD c4 and the software. Just go to test the car, if you got any errors, screenshot them and send us to judge where the problem is.
Q: Does MB SD C4 support SCN coding?
A: Our SD C4 hardware support offline programming, but the software needs to active, and it will cost additional money.
Q:MB SD C4 could read chassis number for Smart 1998, but unable to test ECU after connected with the car.
A: It needs login password when test Smart, we have DAS SMART Calculator (Item No. ss27) to help calculate login password.
Q: Which tool can diagnose ML 270 2005 and A class W169 2007?
A: MB SD C4.
Q: Which tool can diagnose Mercedes Benz Trucks, 3335, 1823 and 1413?
A: MB SD C4.
Q: Which tool can diagnose and program for Mercedes Benz BUS body.
A: MB SD STAR C4 .
Q: Where to find Smart TAN CODE in the software of MB SD C4 ?
A: Sorry, so far we have no Smart TAN code, advice you go to 4S store or original factory to consult.
